Go to Team Pipeotech
All Collections
Test Reports
Test Reports
Tests and certifications performed to verify the capacity and quality of the DeltaV-Seal
16 articles in this collection
Written by
Jarle Ribler
and
Christoffer Næss
Is DeltaV-Seal type-approved?
The DeltaV-Seal is type approved by DNV-GL. The DeltaV-Seal is the world’s first type approved gasket.
Written by
Jarle Ribler
Updated over a week ago
How resistant is the DeltaV-Seal to vibrations and pressure pulses?
The DeltaV-Seal is very resistant to vibrations, as the DeltaV-Seal is a single metal gasket, sealing directly metal to metal.
Written by
Jarle Ribler
Updated over a week ago
Have you tested the DeltaV-Seal performance in respect of fire safety?
Operations which handle large quantities of flammable liquids and gases must rely on the total integrity of their piping infrastructure.
Written by
Jarle Ribler
Updated over a week ago
Can the DeltaV-Seal seal a flange with scribes or a damaged flange surface?
Testing was conducted in order to evaluate the capability of the DeltaV‐Seal to compensate for dents and damages in the RF area of a flange.
Written by
Jarle Ribler
Updated over a week ago
EN 13555 Tests
EN 13555 Leakage test. How does DeltaV-Seal perform?
Compression test, creep/relaxation test and leakage test
Written by
Christoffer Næss
Updated over a week ago
TA Luft VDI 2440
Has DeltaV-Seal been tested according to TA-Luft VDI 2440 guidelines?
'TA-Luft' is an air quality regulation that has set requirements for emissions, ambient exposures, and control methods
Written by
Jarle Ribler
Updated over a week ago
Cryogenic Tests
Cryogenic test at -196°C of DeltaV-Seal, material 316L
The test presents leakage rate measurements of a bolted flange joint (BFJ) using a DeltaV-Seal gasket
Written by
Jarle Ribler
Updated over a week ago
Shell Acceptance Tests for Gaskets (MESC SPE 85/300)
Shell Tests - Goal of Investigation
(MESC SPE 85/300) The goal was to determine how the DeltaV-Seal performed according to this Shell Specification
Written by
Jarle Ribler
Updated over a week ago
Shell 3.3.1 Visual Examination
(MESC SPE 85/300 - 3.3.1) Test specimen DeltaV-Seal
Written by
Jarle Ribler
Updated over a week ago
Shell 3.3.2 Fugitive Emissions Test
(MESC SPE 85/300 - 3.3.2) Shell leakage test was carried out at 25℃, DeltaV-Seal™ was also tested at elevated temperature 400℃
Written by
Jarle Ribler
Updated over a week ago
Shell 3.3.3 - API 6FB Fire Test
(MESC SPE 85/300 - 3.3.3) API 6FB Fire Test >650 ℃ - Verification and qualification of DeltaV-Seal fire resistance
Written by
Jarle Ribler
Updated over a week ago
Shell 3.3.4 ROTT DIN EN 13555-Test
(MESC SPE 85/300 - 3.3.4) Room Temperature Operation Tightness test according to EN13555 Standard
Written by
Jarle Ribler
Updated over a week ago
Shell 3.3.5 HOTT-Test cycle test at 400 ℃
(MESC SPE 85/300 - 3.3.5) HOTT Shell cycle test at 400 ℃, Helium as the test gas
Written by
Jarle Ribler
Updated over a week ago
Shell 3.3.6 Hot Blowout Test (HOBT-1)
(MESC SPE 85/300 - 3.3.6) Hot Blowout Test
Written by
Christoffer Næss
Updated over a week ago
Shell 3.3.8 Gasket Adhesion Test
(MESC SPE 85/300 - 3.3.8) Adhesion test for DeltaV-Seal
Written by
Christoffer Næss
Updated over a week ago
Shell 3.3.14 BAM test for Oxygen
(MESC SPE 85/300 - 3.3.14) Why is this test not applicable for DeltaV-Seal?
Written by
Jarle Ribler
Updated over a week ago